paper cone machine operation
2020/3/9 view:
1. Wear personal protective equipment correctly.
The dress must be worn, shouldn't wear don't wear it must be.Such as paper tube woman worker protection cap when machining requirements, if you don't wear can the hair lay inside.Don't wear the gloves requirements at the same time, if wear, rotating part of the paper tube machinery could heave in the glove, to join hands hurt, paper tube in the operation of the machinery and equipment in safety checks by the regulation.Especially for fastening pieces to see if loosening due to vibration, so that retightened, before operation for paper tube machine equipment safety checks, and to run idle, and confirmed after normal, before put into operation.Forbidden zone fault operation, must not make do use, in case of an accident, paper tube machinery equipment in operation, it is forbidden to use hand to adjust;Also can not measure the parts with the hand, or for lubrication, cleaning stuff, etc.Such as must be, should be first closure of machinery and equipment, paper tube machinery equipment using the tool, tooling and machining parts, such as loading card must be strong, must not be loose.Mechanical safety device must be used properly and in accordance with the provisions, must not to tear down not to use it.Paper tube machinery equipment operation, the operator shall not be allowed to leave the job, just in case nobody disposal, if a problem occurs after the work, should shut down switch, the cutting tool and workpiece exit from the work position, and clean up the work site, the parts, tooling and other neat, clean the paper tube machinery health as well.
2 paper cone machine operation rules
Open run idle 1 to 2 minutes, equipment normal after the operation. Spiral paper cone machine must be someone who's in charge, it is forbidden to others casually misuse. Each part of the machine tool in it is strictly prohibited to put CARDS, measuring tool and other sundry, operation staff shall not leave work. To adjust before cutting tool, clamping the work.Parking barrier to fixed, clamping, loosen, forward, backward, such as order after the trial, before work.Any part of the machine tool in turns, the body may not contact transmission parts.Operation, to plunge into good cuff, it is forbidden to wear gloves to work.The spindle speed should be carried out after parking.With speed gears mesh to fully.Machine tool found abnormal, should immediately stop check.Use grinding wheel cutter, should check whether there is any defect of crack on grinding wheel piece, be affected with damp be affected with damp, the power cord is reliable.Changing cutting tools, measuring work-piece, lubrication, cleaning tube head, must stop.
The dress must be worn, shouldn't wear don't wear it must be.Such as paper tube woman worker protection cap when machining requirements, if you don't wear can the hair lay inside.Don't wear the gloves requirements at the same time, if wear, rotating part of the paper tube machinery could heave in the glove, to join hands hurt, paper tube in the operation of the machinery and equipment in safety checks by the regulation.Especially for fastening pieces to see if loosening due to vibration, so that retightened, before operation for paper tube machine equipment safety checks, and to run idle, and confirmed after normal, before put into operation.Forbidden zone fault operation, must not make do use, in case of an accident, paper tube machinery equipment in operation, it is forbidden to use hand to adjust;Also can not measure the parts with the hand, or for lubrication, cleaning stuff, etc.Such as must be, should be first closure of machinery and equipment, paper tube machinery equipment using the tool, tooling and machining parts, such as loading card must be strong, must not be loose.Mechanical safety device must be used properly and in accordance with the provisions, must not to tear down not to use it.Paper tube machinery equipment operation, the operator shall not be allowed to leave the job, just in case nobody disposal, if a problem occurs after the work, should shut down switch, the cutting tool and workpiece exit from the work position, and clean up the work site, the parts, tooling and other neat, clean the paper tube machinery health as well.
2 paper cone machine operation rules
Open run idle 1 to 2 minutes, equipment normal after the operation. Spiral paper cone machine must be someone who's in charge, it is forbidden to others casually misuse. Each part of the machine tool in it is strictly prohibited to put CARDS, measuring tool and other sundry, operation staff shall not leave work. To adjust before cutting tool, clamping the work.Parking barrier to fixed, clamping, loosen, forward, backward, such as order after the trial, before work.Any part of the machine tool in turns, the body may not contact transmission parts.Operation, to plunge into good cuff, it is forbidden to wear gloves to work.The spindle speed should be carried out after parking.With speed gears mesh to fully.Machine tool found abnormal, should immediately stop check.Use grinding wheel cutter, should check whether there is any defect of crack on grinding wheel piece, be affected with damp be affected with damp, the power cord is reliable.Changing cutting tools, measuring work-piece, lubrication, cleaning tube head, must stop.
- Pre：None
- Next：Paper cone machine meet the ne 2014/6/8
